16X1 HDMI KVM Switch 4K@60Hz
HDMI 모니터 콘솔에서 접속 및 쉽게 제어할 수 있는 8포트 HDMI KVM 스위치입니다.
HKS1601A1U은 USB 2.0 허브 및 USB 2.0 키보드 / 마우스를 지원합니다. USB 2.0
허브포트는 USB 드라이브, 프린터, 바코드 스캐너 등 기타 USB 주변장치를 KVM에
연결하여 사용할 수 있습니다. 전면 패널 버튼, RS232 명령, IP 명령, IR 리모컨 및 키보드
핫키와 같은 다양한 방법을 통해 쉽고 유연하게 전환할 수 있습니다. 모든 입력 포트에
EDID 에뮬레이터를 사용하면 PC에 항상 올바른 디스플레이 정보를 유지하고 입력 포트를
전환하는 동안 디스플레이 설정이 변경되는 것을 방지할 수 있습니다.
Features
l With EDID emulators in each input port, keep PCs always having correct display information
l Support hot plug, connect or disconnect devices to the KVM at any time without turning off devices
l Support front panel buttons, IR signals, keyboard hot keys, RS232 serial commands or IP commands to control KVM switch
l Available to use keyboard and mouse without any delay after switching input sources
l With extra standard USB 2.0 hub port, it is possible to connect bar code scanner, USB hard drive or other USB devices to KVM
l Supports DVI-D single link sources and displays with the use of HDMI-to-DVI adapters
Panel Descriptions
ID | Name | Description |
1 | IR in | Connect IR receiver extension cable to this port, then it is able to use IR control even the KV switch is installed in a rack |
2 | DC 12V | 12V DC power supply |
3 | RS 232 | Connect this port to any control termination, then it is able to select the input sources by sending RS232 commmands |
4 | USB2.0 port | For USB2.0 devices, for example printers, USB hard disk, barcode scanner, touch pad,etc |
5 | HDMI output | Connect to HDMI display |
6 | Keyboard and mouse input | For USB keyboard and mouse input, including wireless keyboard and mouse |
7 | HDMI input | Connect to HDMI sources |
8 | USB data | Connect to computer by USB Type A to Type B cable |
9 | Auto scan time interval settings | [MIN]: Press [MIN] to loop between 0~59 minutes [SEC]: Press [SEC] to loop between 0~59 seconds [Set]: After setting minutes and seconds, press button [Set] to enter final scan time interval setting |
10 | Status LED | Red: Turn off auto scanning mode Green: Turn on auto scanning mode |
11 | IR receiver | Receive IR signal |
12 | LED display | Display current selected input port |
13 | Keypad | [1~16]: Press these buttons to directly select input 1~16 sources [Scan]: Press this button to start or stop automatically scan between input 1 to input 8. The interval time can be set by buttons [Set], [MIN], [SEC] as described above |
14 | LAN port | By connecting to the LAN through this port, you can use the terminal device in the same LAN to send TCP/IP commands to control the switching of input port |
15 | Power switch | Turn on or off power supply |
Connection Diagram
Specification
HKS1601A1U | 16x1 HDMI KVM Switch | |
Functionality: | ||
Auto Scan | Yes | |
Port selection | Front panel buttons | Yes |
Keyboard hotkeys | Yes | |
IR remote control | Yes | |
Console commands | RS232 / IP | |
Technical: | ||
Max. Resolution | 3840x2160@60Hz | |
Auto to get EDID | Yes | |
Data rate | 18 Gbps | |
Auto scan interval | 5~3600 Seconds | |
Beep Sound | On/Off | |
OSD | No | |
Supported OS | Unix/Windows/Debian /Ubuntu /Fedora /Mac OS X/ Raspbian /Ubuntu for Raspberry Pi and other Linux based system | |
Console ports | Keyboard emulation | 1 * USB Type A |